产品中心
新闻动态 当前位置:首页>新闻动态>新闻动态

电力检查井模具生产技术与信息技术交叉融合

网址:www.zhenxinmoju.com  2020-11-18  作者:admin    阅读:

电力检查井模具生产技术与信息技术交叉融合,模具行业数字化成为信息技术改造传统产业和实现信息化带动产业升级的突破口,数字化的模具产业将会成为发展海外市场的关键。
Electric power inspection well mold production technology and information technology cross fusion, mold industry digitization has become the breakthrough of information technology transformation of traditional industry and the realization of informatization driven industrial upgrading, digital mold industry will become the key to the development of overseas market.
一般来讲, 电力检查井模具工作时受变形抗力小,受热、受压、受磨损情况不严重。因此,冷作、热作模具钢相比,他的基本性能要求并不太高,主要性能时有较高的硬度、淬透性良好,淬硬层深,有足够的强韧性,对某些塑料产品来讲,对模具钢还要求有一定的耐蚀性。塑料模具钢结构复杂,精度要求高,其工艺性能也必须有保证。如热处理变形小,有较好的淬透性,机加工性能好,优良的抛光性以及耐磨性能等。
Generally speaking, the deformation resistance of electric inspection well mold is small, and the heating, pressure and wear are not serious. Therefore, compared with the cold working die steel and the hot working die steel, its basic performance requirements are not too high. The main properties include high hardness, good hardenability, deep hardened layer, sufficient strength and toughness, and certain corrosion resistance is required for some plastic products. The steel structure of plastic mould is complex, the precision is high, and its technological performance must be guaranteed. Such as small heat treatment deformation, good hardenability, good machining performance, excellent polishing and wear resistance.
生产电力检查井模具,材料的选择很重要,它直接影响着模具的质量寿命。要多方面考虑,除使用性能和工艺性能外,通用性及价格也不可忽视,模具钢一般用量不大,为了便于备料,应尽可能的考虑钢的通用性,尽量利用大量生产的通用型模具钢,以便于采购‘备料和材料管理。另外还必须从经济上进行综合分析,考虑电力检查井模具的制造费用、工件的生产批量和分摊到每一个工件上的模具费用。从技术、经济方面全面分析,以最终选定合理的模具材料,这样生产出来的钢模具才能受到广大客户的认可。
The selection of material is very important in the production of electric inspection well mould, which directly affects the quality life of the mould. In addition to the use performance and process performance, the versatility and price can not be ignored. Generally, the amount of die steel is not large. In order to facilitate material preparation, the versatility of steel should be considered as much as possible, and the mass production of general profile die steel should be used as much as possible, so as to facilitate material preparation and material management of procurement. In addition, it is necessary to make a comprehensive economic analysis, considering the manufacturing cost of the power inspection well mold, the production batch of the workpiece and the mold cost allocated to each workpiece. From the technical and economic aspects of a comprehensive analysis, in order to ultimately select a reasonable die material, so that the steel mold produced can be recognized by the majority of customers.

返回新闻

电话
15612244999